ZEBRA Z4MPLUS 200 DPI DRIVERS DOWNLOAD

Install E-ring retainers in grooves of roller shaft. Preventive and Corrective Maintenance Section 4 Changeover Printhead A field installable option for Z4Mplus permits changing the printhead density and drive system from dpi to dpi. Once every six months. Enter text from picture: Open the media door and reinstall the mounting screw and lock washer Reinstall the media and ribbon, and close the media door. Rotate the compound pulley aligning the two set screws with the flat spots on the platen roller shaft. See Set Printhead Pressure on page Make sure that the media guide and media supply guide touch the edge of the media.

Uploader: Akik
Date Added: 13 May 2016
File Size: 44.57 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 11726
Price: Free* [*Free Regsitration Required]

Open the pivot bracket assembly by pivoting the module toward you.

Zebra Z4Mplus Maintenance Manual

Printhead Pressure Adjustment This adjustment may be necessary if printing is too light on one side or if thick media is used. Depending on installed options, your printer may look slightly different.

Remove the latch cover by prying out on the front edge with a small screwdriver. Slide the front cover to the right, then zebra z4mplus 200 dpi to remove.

Check media guide position. Don’t show me this message again. The printer needs to see different characters to function properly. Table of Contents Add to zebra z4mplus 200 dpi manuals Add.

zebradesigner pro 2破解版|斑马条码打印机软件下载 v中文破解版 – 多多软件站

Illustration call-out instructions are used when an illustration contains either information about a dialog box, step s to accomplish, or numbers in a table. Page of Go.

Troubleshooting The zebra z4mplus 200 dpi is set for non- continuous media, but continuous media is loaded. All communication parameters are password protected. Page 54 Web sensor is used zebra z4mplus 200 dpi most labels, unless the label liner has black marks on the back.

Read our new white paper. All rights are reserved. Preventive And Corrective Maintenance Figure Close the printhead assembly. Insert the two mounting screws and washer through the strike plate and into the print mechanism.

Peel Option Assembly L Rev. Section 5 Table Remove The Ribbon 3. Parallel Port Interconnections The table below shows the pin configuration and function of a standard computer-to-printer parallel cable. Calibration may clear error conditions that prevent media movement. Slide in the media guide until it just touches, but does not restrict, the zebra z4mplus 200 dpi of the media.

Push the end cap in slightly, then insert the tip of a flat blade screwdriver into the slot in the end cap and turn clockwise to engage it.

Page Align the other access hole of the rewind back plate to the other mounting hole on the rewind support. Don’t have zeebra account?

Supported Labeling Printers

Problem Loss of printing registration on labels. Page Align the other access 20 of the rewind back plate to the other mounting screw and remove the screw.

Page Align the clamp insulator holes with the holes in the pad and z4mplua the insulator on top. Page 47 If the media tends to shift to the right zebra z4mplus 200 dpi printing, increase the left dial setting one position or decrease the right dial setting one position. Pivot up the stepper motor and remove the drive belt. Remove existing cutter assembly.

An OE indicates an overrun error. Install Front Panel Refer to the detail in Figure and route the new front panel ground cable through the hole and into the printer. Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom.

zebra z4mplus 200 dpi

Unless an out-of-ribbon or out-of-media condition exists, ribbon and media error conditions are cleared zebra z4mplus 200 dpi calibration. Positive numbers adjust the label top position further down the label zebra z4mplus 200 dpi from the printhead ; negative numbers adjust the position up the label toward the printhead. Turn the spindle assembly counterclockwise a few times to snug the liner.

The process is now complete. Be sure to note the routing of the cable inside the electronics opening. Page Section 5 Table